Skip to content

About Sphere Design Hub

Structural design you can check.

Sphere Design Hub is a browser based design environment for reinforced concrete. Describe the member, its loads and its supports, and receive a complete design with the working shown, clause by clause, ready to submit.

FIG. 01Two span continuous beam, moving point load
P = 100 kNABCBENDING MOMENT, kNm124.5-52.8SHEAR FORCE, kN
2.60 m
RA
47.9 kN
RB
60.9 kN
RC
-8.8 kN
Mspan
124.5 kNm
MB
-52.8 kNm
Solved in your browser from the three moment equation, spans of 6 m. The same mechanics, at full depth, run inside Sphere Design Hub.
Design basis
EN 1992-1-1 (Eurocode 2) with the UK National Annex
Design modules
Nine reinforced concrete elements
Output
Calculation reports, drawings and bar schedules in PDF
Runs in
Any modern browser. Nothing to install.

01The problem

Why we built it

Concrete design in practice is still spread across spreadsheets, hand calculations and desktop packages that return an answer without showing how it was reached. That is a real difficulty for the engineer who has to sign the drawing, and a larger one for the engineer who has to check it.

A result is only useful if the working behind it can be read, challenged and defended. Sphere Design Hub was built around that idea.

02Nine modules

What it designs

An engineer describes the member, its loads and its support conditions, and receives analysis, section sizing, reinforcement, serviceability checks and a calculation report that cites the governing Eurocode clause for every step.

  1. 01Beam
  2. 02Continuous Beam
  3. 03Column
  4. 04One-Way Slab
  5. 05Two-Way Slaball nine edge cases
  6. 06Continuous One-Way Slab
  7. 07Pad Foundation
  8. 08Combined Footing
  9. 09Staircase
Two way slab input
Two way slab input page with the nine edge continuity cases and plan preview
Pad footing input
Pad footing input page with column details, footing geometry and live footing plan
Column input
Column input page with classification, bracing, end conditions and load take-down

03How it works

Inside the engine

The analysis and design engine is our own work, written in Python and exposed through a typed API. It runs to more than eight thousand lines of solver and code checking logic, developed against worked examples and the corrections of practising engineers.

Analysis
Continuous slabs are solved with a linear elastic stiffness model and a banded symmetric solver, with pattern loading applied automatically. Continuous beams are analysed with pinned or fixed ends. The report sets out the moments and shears at every support and span, so a checker can follow them back.
Columns
Braced and unbraced members, slenderness and second order effects, biaxial bending, sub-frame moments, and load take-down from tributary areas and floor loads when the axial force is not known in advance.
Foundations
Pad footings and two-column combined footings, including pedestals, offset columns, water table effects, bearing pressure and punching shear, with automatic sizing when you want it.
Serviceability and detailing
Deflection, crack control on continuous members, cover for exposure, anchorage, reinforcement drawings and bar schedules, and bar sizes and spacings that follow the ones the engineer prefers to use on site.
Continuous beam input
Continuous beam input page with span arrangement, end supports, elevation preview and cross section

04Principles

What we believe

P1

The engineer's input is law.

If you fix the cover, the effective depth, the bar diameter or the spacing, the engine designs around that choice and says so in the report. It never substitutes a value quietly.

P2

Checked against independent methods.

Each engine is compared with hand calculations, published worked examples and independent solvers while it is built. Column moment capacity, for example, was cross-checked against the parabola rectangle law integrated in layers over 72 cases. The methodology page records what each check found, including where the software simplifies.

P3

The report is the product.

Every design exports a calculation document with a cover page, clause references, shear force and bending moment diagrams, reinforcement drawings and a bar schedule. It is written to be submitted, not just read on screen.

How the calculations are verified

05Around the calculation

Built for teams

Engineering is done by teams, so Sphere Design Hub includes organisations, projects and role based permissions, a report register where each design is marked checked and then issued, and calculation packages that collect a project's designs into one document.

Quick design mode serves the engineer who needs one element checked in five minutes, with nothing to set up.

Project design hub
Project design hub with the nine element modules and the project's saved designs

06The company

Who builds it

Sphere Design Hub is designed, built and operated by Advanced Systems Global Technology Ltd. We write the hard parts ourselves, we verify what we ship, and we stand behind the result.

Put your next element through it.

Start with a single beam or slab in quick design mode. No installation, no setup, and the full calculation is yours to read.

SDH

Loading...